Clik here to view.
connect two edison board via bluetooth
Hello everyone, I wanted to know if in the present it is possible to connect two edison board via bluetooth to transfer data. I red several topics in the forum and if I understood it is not possible to...
View ArticleRe: 4:3 resolutions don't scale properly on 16:9 laptops
This problem has been reported here: Where is "maintain aspect ratio" for Intel HD 4000 on Windows 8.1? Allan.
View ArticleLooking for Intel Widi for Desktop
Please share the requirements to configure Widi Compatible desktop
View ArticleRe: HD 4400: Can't turn off "Maintain Display Scaling"
This problem has been reported here: Where is "maintain aspect ratio" for Intel HD 4000 on Windows 8.1? Allan.
View ArticleRe: Edison + arduino board with galileo-io (Blink LED doesn't work)
The point is not to use the arduino side of the board.I can make the led light up by using GPIO in shell or by using the mraa library in C.So my LED is working fine. But thanks for your advice.
View ArticleRe: Intel core 2 duo are they still manufacured?
Hello Ankit_Jain, the following link will provide you the list of processors that are still launched in our site. ARK | Compare Intel® Products We are not manufacturing this processor anymore, since...
View ArticleDN2820FYK - No Video
Hi everyone, I'm experiencing the same kind of problem with my newly bought NUC n2820.My NUC does not display anything on the two hdmi monitors I have. So it is impossible to boot anything, plus when...
View ArticleRe: Asus Transformer Book T100TA: No option to maintain aspect ratio
hello Oscarkool, this problem has been reported here: Where is "maintain aspect ratio" for Intel HD 4000 on Windows 8.1? Thanks,
View ArticleClik here to view.
Re: Does Skylake desktop CPUs for Home Users are 8 core?
Thanks for the feedback. Allan.
View ArticleRe: recover the data on the RAID 10 volume
Hi Allan, Do you know what action may trigger the RAID controller to mark all the disk as offline? I only change the SATA data cable to different SATA port on the same motherboard on the same Intel...
View ArticleRe: D34010wyk problems with flash video
Let me help you with this. I would like to get more information about your system configuration so I can have a clear picture of the issue. Can you please provide your dxdiag report here?How to get...
View ArticleRe: Intel HD Graphics with HDMI Over Cat6
Hi Ross Could you please provide the following information? 1, What OS are you using?2, How ling of CAT6 run is it?3, What brand/model of HDMI extender are you using?4, Does the Vivo and display work...
View ArticleRe: The Arduino IDE 1.5.3 for Galileo doesn't work on windows 7 x86 (IT)
Hi vinciolo, I think the issue happens because the OS should be in English, but I'm not talking about change the display language, I mean the OS has to be the English version. I'll recommend you to...
View ArticleRe: How to enable PIN0/PIN1 for UART usage (TX/RX)
Hi Wenlong, The following commands should set up the correct pin multiplexing to enable serial mode on Pins 0 an 1. The key part is the echo of 'mode1' into 'current_pinmux', as that sets the pins...
View ArticleRe: Intel HD 4000 Graphics HELP
Yeah i tried downloading the driver from the intel download center but it wont accept it. Is it really like this when you have a integrated graphic card? Also, is it possible to update my Intel HD 4000...
View ArticleRe: Audio via I2S on edison
we're for now breadboarding our own codec to the edison.Codec we use is the TLV320AIC3104.When this works, we'll create the board.
View ArticleRe: wpa_supplicant keeps crashing
Hi corysurf I’d say you could try by editing the /etc/network/interfaces and set in there your wireless configuration. For example you can delete the line that says "wpa-conf /etc/wpa_supplicant.conf"...
View ArticleRe: GPIO usage in bash
Hi shb, I'll recommend you to check this post: Mapping for digital and analog Arduino pins. I think you might find it very helpful. Check it and let us know if this answered your question. Have a nice...
View ArticleClik here to view.
Re: How to enable PIN0/PIN1 for UART usage (TX/RX)
Thanks for the info! wenlong try the David_J_Hunt's suggestion and tell us what were the results. Have a nice day!
View Article