Re: What is the XDK Emulator IP Address?
Thanks. I was asking a different question. When doing client server development with the server on the Edison board and the client as a HTML5/JS solution built using the XDK. If I want to test the...
View ArticleRe: NUC USB problems
Hi LSMS,I have been getting USB issues too. My issue was that my back USB port was becoming unstable. Sometime it will detect the usb device, other times it won't detect anything. A solution I found...
View ArticleRe: Intel Edison USB host mode
From David's project page:The USB OTG cable was needed for the connection to the camera, but the usual ones had a large usb connector on the end, into which you can plug another cable. That was too...
View ArticleRe: Intel AC7260 limited access after sleep
So I guess in your vocabulary, a professor is anyone who isn't into bashing products or other board members and would rather help other people solve problems. I guess that works for me. I think the...
View ArticleRe: intel s1200btl + adaptec raid 5405z
As Intel has not done official tests with the Adaptec* RAID 5405Z, in particular, on the Intel® Server Board S1200BTL (see the list of tested hardware here), it may or may not work as expected. We do...
View ArticleRe: Intel SSD 530 NAND Write Problem
One thing that I have noticed for sure is that running HWMonitor greatly increases NAND writes. I run HWMonitor when launching a game for the first time to check temperatures. HWMonitor is stored and...
View ArticleRe: Where is the "Edison Native Application Guide" PDF?
I have a copy of that NAG ww33 331192-001 Sept 2014, and considering the advancements in just the last 12 weeks, I myself will be waiting for the new NAG when it comes out.
View ArticleRe: Intel SSD 530 NAND Write Problem
Jonnie, in your post I assume you mean NAND writes went up by 1 GB per hour, not host writes. Host writes would have been 0? Also, I notice that you have an Asus laptop. I am using an Asus Z87-A...
View ArticleRe: Cannot open the Arduino in win 7
Thinks, I have met the same problem too. When I use Locale-Emulator everything is find.
View ArticleClik here to view.
How to get start with the SD-Card Linux?
I know I have a stupid title because I have loads of questions and didn't find good answers yet. First, I got the Intel SD-Card Yocto (1.0.4), and successfully installed to my Galileo Gen 2, and wrote...
View ArticleRe: A disk read error occurred - D54250WYK
No. I did install the chipset driver set from the Sept driver bundle but not the Rapid Storage Technology. Should i?
View ArticleRe: S1200BTLR doesn't support hibernation (S4) ?
Hi! As your inquiry refers to a server board, is there any specific reason why you need to put such a system into hibernation?
View ArticleRe: Intel Galileo - Can't upload sketch while boot from Big Linux Image
Hi,I found that sometimes the error info came with "transfer complete" but it works properly, still don't know why. But if you want to run the sketch via your linux terminal, you can try...
View ArticleRe: Problem setting GPIO
Hi Blue_Alien; Take a look at this link specifically the Example 3 and see how to set it as you want. Regards;CMata
View ArticleRe: Problem setting GPIO
That's exactly the tutorial I am following. The problem occurs when using the commands to set them. See what I quoted in the first post.
View ArticleRe: Problem setting GPIO
Others can probably answer better than I can, especially since I have not played with PWM mode yet on the Edison. Which board do you have? Edison with Arduino or simple breakout board? If you have...
View ArticleRe: S2600CP2 not posting
While the Intel® Xeon® Processor E5-2620 v2 is shown among the compatible processors, the BIOS on the board must be compliant with it; see the Server Products — Processor Compatibility list. If the...
View ArticleRe: How to install Debian on Intel Galileo
Thank you for your answer. I have an SD Card (16Gb Sandisk) which I formatted to FAT32.I have a 4 Gb Kingston USB Stick which I also formatted to FAT32. I followed the steps. Downloaded, copied to the...
View ArticleRe: Problem setting GPIO
Ah, I didn't realize the edison with an arduino breakout has different edison hardware. I just have the mini breakout. I'll give it a go.
View ArticleClik here to view.
Re: Problem setting GPIO
On the Edison Mini Breakout board, GPIO-182 is PWM2 in Pin Mode 1 on J17-1. The MRAA number 0
View Article